Mise à jour V2 sur carte ADVANTECH ou N450

[tom]

suite des tests :
- démarrage de la V2
- toujours écran kkkkkkk (raoulh je t'envoie la photo)
- redemarrage calaos démarré avec ip 10.0.0.3
- connection sur ssh root@10.0.0.3
- la commande connmanctl services me donne ca.
*AR Wired ethernet_000bab452978_cable
*A Wired ethernet_000bab452977_cable

- ifconfig me donne ca :
enp0s25 Link encap:Ethernet HWaddr 00:0B:AB:45:29:77
inet6 addr: fe80::20b:abff:fe45:2977/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:681 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:45993 (44.9 KiB) TX bytes:492 (492.0 B)
Interrupt:23 Memory:feac0000-feae0000

enp3s0 Link encap:Ethernet HWaddr 00:0B:AB:45:29:78
inet addr:10.0.0.3 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::20b:abff:fe45:2978/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1350 errors:0 dropped:0 overruns:0 frame:0
TX packets:81 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:255664 (249.6 KiB) TX bytes:11845 (11.5 KiB)
Interrupt:16 Memory:febe0000-fec00000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:119 errors:0 dropped:0 overruns:0 frame:0
TX packets:119 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7431 (7.2 KiB) TX bytes:7431 (7.2 KiB)

- commande : connmanctl config ethernet_000bab452978_cable --ipv4 manual 10.0.0.3 255.255.255.0 192.168.1.1
- commande : connmanctl config ethernet_000bab452977_cable --ipv4 dhcp
- redemarrage
- a l'ecran le serveur à gardé son ip 10.0.0.3 et je ne vois pas le serveur sur le réseau local

- re test
- commande : connmanctl config ethernet_000bab452978_cable --ipv4 manual 10.0.0.3 255.255.255.0 192.168.1.1
- commande : connmanctl config ethernet_000bab452977_cable --ipv4 dhcp
- commande : connmanctl connect ethernet_000bab452977_cable
- ifconfig
enp0s25 Link encap:Ethernet HWaddr 00:0B:AB:45:29:77
inet addr:192.168.1.48 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20b:abff:fe45:2977/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:740 errors:0 dropped:0 overruns:0 frame:0
TX packets:101 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:57621 (56.2 KiB) TX bytes:22759 (22.2 KiB)
Interrupt:23 Memory:feac0000-feae0000

enp3s0 Link encap:Ethernet HWaddr 00:0B:AB:45:29:78
inet addr:10.0.0.3 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::20b:abff:fe45:2978/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1109 errors:0 dropped:0 overruns:0 frame:0
TX packets:163 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:149070 (145.5 KiB) TX bytes:33697 (32.9 KiB)
Interrupt:16 Memory:febe0000-fec00000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:164 errors:0 dropped:0 overruns:0 frame:0
TX packets:164 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:12138 (11.8 KiB) TX bytes:12138 (11.8 KiB)

- redemarrage
- a l'ecran le serveur à gardé son ip 10.0.0.3 et je ne vois pas le serveur sur le réseau local
- ifconfig me donne ca :
enp0s25 Link encap:Ethernet HWaddr 00:0B:AB:45:29:77
inet6 addr: fe80::20b:abff:fe45:2977/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:259 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:17314 (16.9 KiB) TX bytes:492 (492.0 B)
Interrupt:23 Memory:feac0000-feae0000

enp3s0 Link encap:Ethernet HWaddr 00:0B:AB:45:29:78
inet addr:10.0.0.3 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::20b:abff:fe45:2978/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:396 errors:0 dropped:0 overruns:0 frame:0
TX packets:57 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:58133 (56.7 KiB) TX bytes:8927 (8.7 KiB)
Interrupt:16 Memory:febe0000-fec00000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:102 errors:0 dropped:0 overruns:0 frame:0
TX packets:102 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6348 (6.1 KiB) TX bytes:6348 (6.1 KiB)

---

-------------
Concernant l'écran (surement des erreurs dans ce que je fais:
- DISPLAY=:0 xinput_calibrator me donne ca :
Setting calibration data: 96, 4000, 96, 4000
Calibrating EVDEV driver for "Elo Serial TouchScreen" id=9
current calibration values (from XInput): min_x=96, max_x=4000 and min_y=96, max_y=4000

- cd /usr/share/X11/xorg.conf.d/
- sudo nano 90-calib.conf
- j'y copie ca :
Section "InputClass"
Identifier "calibration"
MatchProduct "XXXXXXXX"
Option "Calibration" "YYYYYYYYY"
Option "SwapAxes" "0"
EndSection

c'est bon ???
par contre je ne sais quelles sont les valeurs qui remplacent xxxx et yyy